FAQ's for the Rev7 Tachograph

How do I know whether I have the Rev7 version of the SE5000?
How do I insert and eject a driver card?
How do I take a 24 h print out from the drivers card?
How do I print local time 24h printout?
How do I select language on the tachograph?
How do I select the activity on the tachograph?
I'd like to change the default mode to Rest when the engine stops, how can I do this?
How do I set the display to the local time.
How do I replace the printer paper?
How can I quickly check that the VU is working fine?
How do I change to Ferry/Out of Scope mode?
How do I download data from the SE5000? (Company mode)
How do I lock in the Company data? (Company mode)
When am I required to lock in the Company data? (Company mode)
Where is the download connector? (Company mode)

How do I know whether I have the Rev7 version of the SE5000?
The buttons on the front of the tachgraph were changed as part of the Rev7 update. You know you have a Rev7 SE5000 if your unit has buttons under the display with the following symbols:

How do I insert and eject a driver card?
Press and hold the  or  button for at least three seconds and the card tray will eject. To remove the card from the tray, press the driver card up slightly from underneath through the opening in the tray or push the edge of the tray down until the card pops out. (Ejecting a card can only be done when the vehicle is stationary.)

How do I take a 24 h print out from the drivers card?
Press the button once to go to the print screen. Press  once more and use the and buttons to select the printout you want. To confirm and to activate the printout, press .

How do I print local time 24h printout?
Press the button once to get to the printing menu. Press the button once more. Use the and buttons to select the printout you want. Commence the selected printout by pressing .

How do I select language on the tachograph?
Press the button. Use the and buttons to select Settings and press . Use the and buttons to select language and press . Use the  and buttons to select your language and press .

How do I select the activity on the tachograph?
Press the  or  button. The selectable modes are Available, Other work and Rest/break. Drive is automatically selected when the vehicle is set in motion.

I'd like to change the default mode to Rest when the engine stops, how can I do this?
You can change the preset to any automatic activity change for both driver & co-driver when switching the ignition off. To do this:

1. Insert a company card or a workshop card in either of the tacograph trays.
2. Press the  button. 
3. Use the and buttons to scroll to the Settings menu and press . 
4. Use the and buttons to select "Parameters" and press . 
5. Use the and buttons to select "Default activ. key off" and press . 
6. Use the and  to select the preferred activity (e.g. "Rest"). 
7. Press OK to confirm. A "Changes Saved" message will appear to confirm the change.

How do I set the display to the local time.
Navigate to the settings by pressing the button from main screen. Next, use the and buttons to scroll to the settings menu. Press to access the settings menu and to scroll to local time and confirm with. You can alter the time in steps of 30 minutes. Press to confirm.

How do I replace the printer paper?
Remove the front cover on the right-hand side of the tachograph by pressing the top of the plastic cover. This will dislodge the cover and allow you to pull the roll.

How can I quickly check that the VU is working fine?
Press the button once and then use the and buttons to navigate to "Settings". In the "Settings" menu you can select "Built in test" to carry out a working test on your SE5000.

How do I change to Ferry/Out of Scope mode?
Press the button once and then use the and buttons to navigate to "Places". In the "Places" menu you can select "Ferry" or "Out of Scope".

How do I download data from the SE5000? (Company mode)
Ensure you have a valid Company card inserted and locked into the tachograph. See Company locks. Connect a type approved Download tool to retrieve the data.

How do I lock in the Company data? (Company mode)
Insert the Company card then press to enter the menu. Use the and buttons to select "Company locks" and confirm with pressing .

When am I required to lock in the Company data? (Company mode)The first time you take delivery of the vehicle you need to insert your Company card to lock in the data.

Where is the download connector? (Company mode)
The connector is located on the left side of the paper roll behind the plastic cover.